Brush on a generous. The advanced alkyd resin with UV absorbers offers excellent durability and protection for siding and other vertical surfaces.
Log homes exterior wood entrance doors garage doors and window frames as well as fiberglass doors.
Sikkens cetol 1 and 23 application guide. Sand surfaces with 180-220 grade grit paper always sand along the length of the grain. CETOL 1 CETOL 23 PLUS PREPARATION application of one coat to all sides of the boards is the best CETOL 1 CETOL 23 PLUS APPLICATIONS Sikkens вЂ I used Cetol 1 to stain Please refer to the Previously Coated Wood section in the Sikkens Application Guide or contact your Wood Stain Finish Supply Center. You will achieve better results if you can avoid applying Cetol in direct sun.
During application saturate all end grains nail holes cavities and cracks in the wood. This results in no air circulation behind the siding to allow for moisture to escape. Allow a minimum of 24 hours dry time between coats.
For airless spray use a 011-015 tip at 700 – 800 psi adjust pressure as needed. FOR USE ON New exterior hardwood and decking. Follow preparation procedure before applying first coat.
Wait 2 years and apply 1 coat of Cetol 23 Plus RE. Since outdoor furniture and fences are considered to be in a high moisture environment it is recommended to apply 2 coats of Cetol 1RE. We are a distributor of Sikkens Exterior and Interior Wood Finishes.
Allow to dry a minimum of 24 hours. Apply one even coat of Cetol 1 RE Wood Finish avoiding heavy application. Cetol 1 TDS Cetol 23 Plus Application Guide Cetol 23 Plus MSDS Cetol 23 Plus RE MSDS Cetol 23 Plus TDS Cetol DEK Application Guide.
Cetol 1 Application Guide. Allow to dry a minimum of 24 hours. Apply a thin coat of Sikkens Cetol 23 to the cleaned area and observe if the patch turns dark.
Clean a spot with a 3 to 1 solution of bleach and water to remove all mold and mildew. 23C 73F Overcoated By Min Max Cetol 24 hours Ext APPLICATION AND USE Preparation NEW EXTERIORINTERIOR WOOD. The Cetol 1 RECetol 23 Plus RE protective systems is.
Apply over existing Cetol 23 Plus or Cetol Log Siding Apply only when the surface is in good condition and has been maintained according to Sikkens maintenance guidelines Apply when the surface and air temperature is 500F100C to 95 OF350C Saturate all end grains nail holes cavities and cracks in the wood. To avoid lap marks start at one edge and follow through to the end of each. – 1 coat of Cetol 1 RE – 2 coats of Cetol 23 Plus RE.
We also carry many other types of coatings for both indoor and outdoor use. A more resilient alternative to exterior varnishes and polyurethanes. 8m2Litre CLEAN UP Water SIZE 1 5 Litres FOR USE ON To brighten and revitalise grey weathered.
All systems consist of three coats. Rinse and allow the wood to dry thoroughly. Cetol 23 Plus RE is a 2 -coat application and enhances wood grain with rich color and signature clarity.
Cetol 1 and Cetol 23 Plus are recommended for use on vertical uncoated surfaces such as fences or shed walls. All three coats must be applied within 30 days after preparation. Cetol 23 Plus RE is a premium translucent topcoat for Cetol 1 RE.
Maintain with periodic single coat of Cetol Maintenance see below. With Sikkens Cetol BL Tannin Oil Remover. Apply in the direction of the grain.
Must be top coated with two coats of Cetol 23 Plus RE Top Coat following label application directions. Cetol 23 Plus RE is a premium translucent satin top coat for Cetol 1 RE. In this case Sikkens recommends the application of a third coat of Cetol Marine Gloss to compensate for the reduced layer thicknessApply all coats within 1-2 weeks.
Must be followed by either Sikkens Cetol BL Deck Wood Cleaner or Sikkens Cetol BL Garden Furniture Cleaner APPLICATION Watering can COVERAGE Approx. Just prior to the application of the Cetol system allow a 6-month exposure time. Sikkens Proluxe Cetol Door and Window is a premium translucent exterior stain whose alkyd high solids formulation offers optimum protection and a distinctive look for these unique areas.
If it does the wall must be stripped of all the old stain per Sikkens instructions. Apply one even coat of 1 Primary Coat RE Wood Finish avoiding heavy application. For wooden furniture Sikkens recommends three coats of Cetol 1 be applied.
Spraying is only recommended for Cetol 23 Plus. Follow preparation procedures One coat Cetol Marine Marine Light or Natural Teak One coat Cetol Marine Marine Light or Natural Teak One coat Cetol Marine Marine. Available as a clear satin clear gloss or 4 ready mix colors in satin.
CETOL 1 CETOL 23 PLUS – TRANSLUCENT SATIN FINISH POOR VENTILATION MEDIUM MOISTURE Poor ventilation and medium moisture exists when the siding is applied directly to tar papersheathingStyrofoamTyvecetc. Apply in the direction of the. Cetol 1 is always used as the first coat in any bare wood application.
Cetol 1 RE remains firmly attached to the wood and provides a perfect surface to accept the next layer of protection Cetol 23 Re Plus. It is essential to remove any surface oils and contaminants prior to sanding and application of Cetol Marine Natural Teak. Then apply 3 coats of Cetol 1 RE.
Must be top coated with two coats of 23 Top Coat RE following label application directions.